Loading... Please wait...

Categories

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
  • Image 9

Front and Rear Stand Assembly

$1.00
SKU:
FRSA
Weight:
0.10 KGS
Shipping:
$1.00 (Fixed shipping cost)
Quantity:
Bookmark and Share


Product Description

Since 2006 Kaneg has been proudly serving Racers, Riders and Enthusiast alike.

We race at the following Circuits, so make a point of catching up;

Eastern Creek, Phillip Island, Broadford, Mac Park, Morgan Park, Wakefield and occasionally QLD raceway, Winton and Hidden Valley, so you are sure to see us sometime.

To see other kaneg products visit us at

https://www.kaneg.com.au

Sydney pickups at 8/51 York Road Penrith 2750.

Contact us at: sales@kaneg.com.au

Rhys 0414712419

Phil 0414968949

 

ASSEMBLY INSTRUCTIONS.

The Front and Rear Stand are similar in Assembly, the differenece being:

The Rear hooked pickup shaft flat side, is secured into place by an Allen Key head screw tightened to 40Nm.

The Front forked pickups are inserted into the circular Stand Leg pivot hole and secured into the stand leg with a spring clip.

 

To Assemble our stands you shall need;

A level surface, on which to engage the stands to lift your bike, if requested we shall supply a level bubble so you can check the stands are on a level surface.

Blue Locktight to the rear hook screws.

1x 6mm Allen Key.

1x 17mm ring spanner.

 

REAR STAND

Lay the stand Handle onto a level surface with the black rubber plastic clip facing the floor

With the handle on the floor, Slide the narrow end of each stand leg into the handle.

These are universal sided stand legs with no Right or Left hand leg.

Fix the legs into the handle by inserting the supplied bolts:

The domed bolt head must be located outside of the stand.

Place one washer on either side on the stands tube, then Tighten the lock-nut to a 40Nm (a very firm feel)

Once assembly is complete

Insert the forked pickup into the top of the stand legs, these forks hook onto your spools, so it is important the securing screws be locktighted and tightened to 40Nm to carry motorcycle.

Locktight and Tighten the bolts, ensure that the taller arm of the hooks are facing forward.

and the flat part of the pickup shaft facing the screw.

Firstly have a dummy run to set the forked pickup position, do not lift the bike until the stand is fully setup.

Measure the spools centre to centre and secure the forked pickup at this measurement, You might need a couple of goes before you get correct distance.

Once the forks are positioned to suit the spools, with the flat part of the pickup shaft facing the screw, tighten the locktighted bolts to 40Nm to secure into position.

 

FRONT STAND

Lay the stand Handle onto a level surface with the black rubber plastic clip facing the floor

With the handle on the floor, Slide the narrow end of each stand leg into the handle.

These are universal sided stand legs with no Right or Left hand leg.

Fix the legs into the handle by inserting the supplied bolts:

The domed bolt head must be located outside of the stand.

Place one washer on either side on the stands tube, then Tighten the lock-nut to a 40Nm (a very firm feel)

Once assembly is complete

Insert the (rubber clad pronged) shaft the stand leg hole with the Spring to the inside of the leg and secured externally by the spring clip

 

The front stand must only be used once a rear stand has been engaged


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!


You Recently Viewed...



MOTORCYCLE ACCESSORIES FOR THE WORLDS LEADING BRANDS

SIGN UP TO OUR NEWSLETTER